Lockeyusa 2835 User Manual download pdf

No.

Part Name

Qty.

Outside Body

Inside Body

Lever Handle

Rubber Trim Plate

Strike Plate

Mortised Striker

Spindle

Allen Wrench

Machine Screw M4 x 40 mm

Machine Screw M4 x 30 mm | 50 mm

1|1

Wood Screw M4 x 16 mm

Extra Code Tumblers (Red)

Extra Non-Code Tumblers (Blue)

Latch (2 3/8” or 2 3/4”)

Support Pin

Tweezers

Hex Bolts

Door Edge

Step 7: Install the Lockey 2835

1. Place the Rubber Trim Plate (#4) on the

backside of the Outside Body (#1).

2. Place the Outside Body

on the door. The hexagonal

bolts (#17) should extend

through the top and bottom

holes.

3. The Support Pin (#15) should fit

into and extend through the hole in the

Latch (#14).

Step 6: Verify Correct Spindle Length

1. With Latch (#14) installed, hold

the Inside Body (#2) and Rubber Trim

Plate (#4) to the door.

2. Place Spindle (#7) through Latch,

into the Inside Body, as far as possible.

3. Spindle should extend from exterior of door

3/8” min. – 5/8” max.

4. If Spindle is too long, cut it to the correct length using Pliers.

IMPORTANT: If spindle extends less than 3/8” it may not engage the lock. If spindle

extends more than 5/8”, it will cause the lock to bind.

Lever Handle (#3)

Step 5: Install Latch

1. Insert Latch (#14) into door.

Note: Latch face should be flush with

the door’s edge.

2. Secure with two (2) Wood Screws (#11).

Step 4: Install Lever Handles

Using Allen Wrench (#8), install levers

to the inside and outside bodies.

Secure with set screws.

Note: Levers should point towards

the door hinges.

Step 3: Identify Door Handing

Right-Hand Doors – From exterior of

door, hinges are on right-side. (Fig. 1)

Left-Hand Doors – From exterior of

door, hinges are on left-side. (Fig. 2)

For Right-Hand Doors: Install the

Support Pin (#15) in position ‘A’.

For Left-Hand Doors: Install the

Support Pin (#15) in position ‘B’.

Now, install/screw Hex Bolts (#17)

into the top and bottom as shown.

Lockey 2835 Lever

Installation Instructions

Step 2: Prep Door for Installation with Template

1. Place template (supplied) on door and fold along door’s edge.

2. Mark holes for 2 3/8” or 2 3/4” backset.

3. Drill holes as instructed.

NOTE: For Pre-Prepped 2 1/8” doors, you only need to drill top hole.

Inside Body (#2)

Spindle (#7)

3/8” to 5/8”

Step 1: Change User Code (OPTIONAL)

If you wish to change your code, see instructions on reverse side.

1 2

Summary of Contents

Page 1 - Installation Instructions

No. Part Name Qty. 1 Outside Body 1 2 Inside Body 1 3 Lever Handle 2 4 Rubber Trim Plate 2 5 Strike Plate 1 6 Mortised Striker 1 7 Spindle 1 8 Allen

Page 2 - How to Change Code

Step 8: Using the Lockey 2835 1. When the door is closed the system will lock automatically. 2. From the inside, unlock using the Lever Handle.

Comments to this Manuals

No comments

Lockeyusa 2835 User Manual

Browse online or download User Manual for Safety Lockeyusa 2835. LockeyUSA 2835 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Lockeyusa 2835